FMT | Frezite Metal Tooling

157 Frezite Metal Tooling LEGIERTE STÄHLE / Werkzeug- und Formenbau | Bohren ALLOY STEEL / Mould and Die | Drilling www.fmttooling.com Material Werkstoff Tensile strength (N/mm 2 ) Hardness (HB) Zugfestigkeit N/mm 2 Härte (HB) Cutting speed Vc (m/min) Schnittgeschwindigkeit Vc (m/min) Recommended feed f (mm/rev) for diameter ranges Empfohlene Vorschubgeschwindigkeit f (mm/Umdrehung) in Abhängigkeit des Schneidendurchmessers External coolant Externe Kühlung Internal coolant Interne Kühlung Ø 3-5 mm Ø 5-8 mm Ø 8-12 mm Ø 12-16 mm Ø 16-20 mm Non-alloy steels, cast steel Unlegierte Stähle up to 600 N/mm 2 bis zu 600 N/mm 2 85-100 95-115 0,10-0,18 0,15-0,25 0,18-0,30 0,20-0,35 0,25-0,40 up to 700 N/mm 2 bis zu 700 N/mm 2 75-90 85-105 0,10-0,18 0,15-0,25 0,18-0,30 0,20-0,35 0,25-0,40 over 700 N/mm 2 über 700 N/mm 2 65-80 75-90 0,10-0,20 0,15-0,28 0,18-0,35 0,20-0,38 0,25-0,42 Alloy steel Legierte Stähle up to 900 N/mm 2 bis zu 900 N/mm 2 55-75 60-85 0,10-0,20 0,15-0,28 0,18-0,35 0,20-0,38 0,25-0,42 up to 1000 N/mm 2 bis zu 1000 N/mm 2 45-60 50-70 0,10-0,15 0,12-0,20 0,14-0,25 0,14-0,25 0,18-0,32 over 1000 N/mm 2 über 1000 N/mm 2 35-50 40-60 0,10-0,15 0,12-0,20 0,14-0,25 0,16-0,30 0,18-0,32 Inox 40-60 50-70 0,04-0,10 0,06-0,12 0,08-0,15 0,12-0,20 0,15-0,25 Stainless steel (Cr-Ni-alloys) Edel- und säurebeständige Stähle (CrNi-Leg.) 30-50 40-60 0,03-0,08 0,04-0,10 0,06-0,12 0,08-0,15 0,08-0,15 Grey cast iron, grey cast iron alloy Grauguß und legierter Grauguß up to 200 HB bis zu 200 HB 70-110 80-130 0,10-0,25 0,15-0,30 0,20-0,40 0,25-0,45 0,30-0,50 up to 250 HB bis zu 250 HB 60-95 70-115 0,10-0,20 0,12-0,25 0,15-0,35 0,20-0,40 0,25-0,45 over 250 HB über 250 HB 50-80 60-100 0,10-0,20 0,12-0,25 0,15-0,35 0,20-0,40 0,25-0,45 Spheroidal graphite cast iron, cast iron with vermicular graphite, malleable iron Kugelgraphit, Vermicularguß, Temperguß up to 600 N/mm 2 bis zu 600 N/mm 2 65-85 75-90 0,10-0,20 0,12-0,25 0,20-0,35 0,30-0,40 0,35-0,50 over 600 N/mm 2 über 600 N/mm 2 55-70 65-80 0,08-0,15 0,10-0,20 0,18-0,30 0,25-0,35 0,30-0,40 Aluminium (SI content > 10%) Aluminium (Si-Gehalt < 10%) 110-360 110-360 0,10-0,25 0,15-0,35 0,25-0,45 0,30-0,50 0,35-0,55 Aluminium (SI content < 10%) Aluminium (Si-Gehalt > 10%) 120-480 120-480 0,10-0,25 0,15-0,35 0,25-0,45 0,30-0,50 0,35-0,55 Copper, brass, bronze Kupfer, Messing, Bronze 120-480 120-480 0,10-0,25 0,15-0,35 0,25-0,45 0,30-0,50 0,35-0,55 Titanium alloys Titaniumlegierungen 20-40 20-50 0,02-0,07 0,04-0,10 0,06-0,12 0,08-0,15 0,08-0,15 Nickel alloys Nickellegierungen 20-40 20-50 0,02-0,07 0,04-0,10 0,06-0,12 0,08-0,15 0,08-0,18 9103, 9105, 9476, 9477 Art. SOLID CARBIDE TWIST DRILLS SPIRALISIERTE VHM - BOHRER ▪ The guideline values for cutting speed (Vc) should be multiplied by the following correction factors (KFv) according to the boring depth. ▪ Die Richtwerte der Schnittgeschwindigkeiten (Vc) sollten mit den angegebenen Korrekturwerten (KFv) der jeweiligen Bohrtiefen multipliziert werden. Boring Depth Bohrtiefe KFv 1xD 1,3 2xD 1,2 3xD 1 Boring Depth Bohrtiefe KFv 4xD 1 5xD 0,8 8xD 0,7 12xD - Reco mmended Cutting Parameter / Empfohlene Schnittparameter TEC HNICAL INFORMATION / TECHNISCHE INFORMATIONEN

RkJQdWJsaXNoZXIy NDkzNTY=